Introduction to Three leaf Roots blower for steel industry and Three leaf Roots blower advantages and features

Three leaf Roots blower for steel industryis a double impeller synchronous compression machine, belonging to a positive displacement blower.，multifunctional, with functions such as pick up the suction, desulfurization oxidation, sewage disposal, cool and mix，was developed and designed by hyde。The following is to introduce the Three leaf Roots blower for steel industry:

1、Brief introduction of Three leaf Roots blower for steel industry

Three leaf Roots blower for steel industryis a positive displacement blower with forced gas transmission characteristics.，Cheap and high quality。

Three leaf Roots blower for steel industry

2、Three leaf Roots blower for steel industry advantage

The advantages of Three leaf Roots blower for steel industry are as follows:

1. Economical and durable

The design without lubrication reduces the maintenance cost and improves the economy of the equipment.

2. Stable air output

Due to the design of three-blade rotor, the Three leaf Roots blower for steel industry has little vibration and low noise during operation, and the operation is stable and reliable.

3. Wide application range

Widely used in many fields, such as commodity industry, etc., it is more suitable for gas transportation and pressurization systems in low-pressure occasions, and can also be used as vacuum pumps.

4. Convenient maintenance

The structure of the Three leaf Roots blower for steel industry is relatively simple and easy to maintain.

5. Durable performance

Impeller and shaft are integrated structure, and the impeller is not worn, so the performance of the fan is durable and can run continuously for a long time.

Three leaf Roots blower for steel industry

3、Three leaf Roots blower for steel industry use

Three leaf Roots blower for steel industryCommonly used inmaterial handling,sewage disposal,supply air,mix,aeration and so on。

Three leaf Roots blower for steel industry

4、Three leaf Roots blower for steel industry principle

Three leaf Roots blower for steel industryat the start of the operation,The gas is compressed and transported by the relative rotation of a pair of trilobal rotors in the cylinder. Each trilobal rotor is supported by two bearings, and the relative position of the two rotors is always kept constant by using a pair of synchronous gears. During the rotation of the rotor, there are tiny gaps between impeller and impeller, impeller and casing, impeller and side cover, so there is no friction in the working chamber and no lubrication is needed, thus realizing the smooth transportation of gas.。

Three leaf Roots blower for steel industry

5、Introduction of Three leaf Roots blower for steel industry characteristics

Three leaf Roots blower for steel industrysmooth operation,low noise,convenient maintenance,strong adaptability,wide application range，is a popular Three leaf Roots blower for steel industry，the advantage is Due to the adoption of synchronous gear transmission and small gap design, the Three leaf Roots blower for steel industry runs stably and reliably, without contact and wear parts, and has a long service life.、The structural form of the three-blade rotor and the reasonable structure of the air inlet and outlet in the shell make the fan have small vibration and low noise.、Because of the design of three-blade rotor, the Three leaf Roots blower for steel industry has little vibration and low noise during operation, and the operation is stable and reliable、Due to the adoption of synchronous gear transmission and small gap design, the Three leaf Roots blower for steel industry runs stably and reliably, without contact and wear parts, and has a long service life.、The air volume is directly proportional to the rotating speed, so its air output is very stable and basically unaffected by pressure changes. This characteristic makes the Three leaf Roots blower for steel industry perform well in many situations where stable airflow is needed.，Gas is compressed and transported based on the relative motion of two lobed rotors in the cylinder. When the two rotors rotate, the volume between them changes constantly, thus realizing the suction, compression and discharge of gas.，customizable。

Three leaf Roots blower for steel industry

6、Three leaf Roots blower for steel industry structure composition

The Three leaf Roots blower for steel industry structure is introduced as follows:

1. wallboard

It is mainly used to connect the casing with the impeller, support the rotation of the impeller, and play the role of end sealing.

2. impeller

It is the rotating part of the Three leaf Roots blower for steel industry, which is divided into two leaves and three leaves. However, due to many advantages such as smaller air pulsation, less noise and smoother operation, the three-leaf Three leaf Roots blower for steel industry has gradually replaced the two-leaf Three leaf Roots blower for steel industry.

3. case

It mainly plays the role of supporting (wallboard, impeller, muffler) and fixing. The casing is the external structure of the Three leaf Roots blower for steel industry, which is used to support and fix the rotor, bearings and other components, while ensuring the gas tightness.

4. impeller

It is the rotating part of the Three leaf Roots blower for steel industry, which is divided into two leaves and three leaves. However, due to many advantages such as smaller air pulsation, less noise and smoother operation, the three-leaf Three leaf Roots blower for steel industry has gradually replaced the two-leaf Three leaf Roots blower for steel industry.

5. wallboard

It is mainly used to connect the casing with the impeller, support the rotation of the impeller, and play the role of end sealing.

Three leaf Roots blower for steel industry

Three leaf Roots blower for steel industryis a Three leaf Roots blower for steel industry，it has the characteristics of strong adaptability, low noise, economical and durable, run smoothly and Precise control，The overall structural design is relatively simple and compact.，it has the structure of wallboard, case, impeller, wallboard and bearing。